KOMLINE SANDERSON KOMPRESS MODEL G-GRSL-1 SERIES III BELT FILTER PRESS

ITEM 902:  KOMLINE SANDERSON KOMPRESS MODEL G-GRSL-1 SERIES III BELT
FILTER PRESS

This Komline Sanderson
Belt Press equipment is located at the WWTP in Farmville, NC.  For now we
are quoting the equipment as is, still installed at the Farmville, NC WWTP
facility.  It would be the responsibility of the buyer to carefully remove
and load the equipment and leave the facility in a clean and dry
manner. This equipment was installed in Farmville, NC in 2007 and never
actually run in production mode for any extended period of time.  It has
run less than 15 days total in a startup-demonstration mode only.  We have many photos, pdf files, drawings, and
manuals available for further evaluation if needed.  A brief summary of the belt press is as
follows: 

A.) Komline
Sanderson Kompress Belt Filter Press Model G-GRSL-1
Series III.. Komline Sanderson EC Job # S-3922 

Active Width:  1.0 meters

Filter Belt
Width:  1.2 meters (47”) 

Filtration Areas:

            Gravity Zone:  52 square feet

            Wedge Zone:  22 square feet

            Pressure/Shear Zone:  69 square feet 

Dimensions: 

            Length:  21 feet, 10 inches

            Width:  7 feet, 6 inches

            Height:  8 feet, 10 inches 

Dry Weight:  16,000 pounds. 

Service
Requirements: 

            Washwater:  66 gpm @ 85 psi

            Electrical:  See Control Panel Specificiations

            Hydraulic:  2 gpm @ 900 psi 

Material of
Construction, main frame:  Hot dipped
galvanized carbon steel.  Fasteners:  316 stainless steel.  Inlet Distributor, Leveling Dam, Filtrate
Collection pans:  316 stainless steel 

Number of Pressure
Drums:  Eight (8) 

Filter Belts:  Komline Sanderson Model KS-4086, monofilament
polyester, modified satin, 391 cfm; 42.2 oz/square yard with 316 L stainless
steel clipper seam with polyurethane reinforcement.

Drives: 

            Gravity Belt Drive Assembly:

                        Motor: 2 HP Eurodrive
motor, 1800 rpm, 3/60/460 TEFC severe duty

                        Reducer:  Eurodrive, Model KA 87 AGMA Class II, 85.65:1.0
ratio; 8.4 HP           

                                    input
rating;  18,000 inch-lbs output rating.

                        Gravity Belt Speed:  5-50 fpm.                                   

            Pressure Belt Drive Assembly:

                        Motor: 2 HP Eurodrive
motor, 1800 rpm, 3/60/460 TEFC severe duty

                        Reducer:  Eurodrive, Model KA 87 R57, AGMA Class II,
236:1.0 ratio; 2.0           

                                    HP input
rating;  23,900 inch-lbs output rating.

                        Gravity Belt Speed:  2-20 fpm.

Dewatering Drums and
Rollers:  316 stainless steel perforated
dewatering drum, 30 inch diameter.  See
complete 22 page Specifications for more complete details of all the drums and
rollers 

B.)   Hydraulic
Power Unit – (filter press mounted):  Nachi variable
volume, pressure compensated pump set at 2.5 gpm, 900 psi.  Motor is Baldor 1.5 HP, 1800 rpm, TENV 1.15
service factor, 3/60/230/460 washdown duty. 
Reservoir is 316 stainless steel, 5 gallon capacity, factory mounted on
press.  All system interconnecting tubing
and fittings are factory furnished and installed using 3/8” O.D. 316 stainless
steel tubing.

C.) Control Panel:  NEMA 4 X stainless steel.  36” wide x 42” tall x 12” deep. Drawing Number
S3922-90001D.  Panel shows control power;
cycle; wash cycle; hydraulic pump; washwater pump; gravity belt drive; pressure
belt drive; was pump 1 and 2; polymer system; alarm; emergency stop; speed indicator
0-50 fpm; speed indicator 0-20 fpm; flow indicator 0-250 gpm; speed indicator
0-100%; effluent pump. Also contains Moxa EtherDevice Switch EDS-205 Industrial
five port unmanaged ethernet switch.  All
switches and pilot lites are of a Square D corrosion resistant design.

D.) Drawings and Manuals:  Equipment comes complete with two sets of
manuals and all drawings of components, flowsheets, equipment layout.  

Dismantling and loading will be additional cost.  We encourage the buyer to hire their own
contractor for match marking, dismantling, and loading of the equipment to
facilitate ease of installing at the new location.  Other items on this project may still be available at time of sale ( at additional cost) such as filter feed pumps, filter cake discharge hopper, discharge filter cake Moyno pump, etc)